MontanaBusinessesNear Me
Whole-Home Generator Installation Cost in Montana: Where Every Dollar Goes
← All Posts

electricians

Whole-Home Generator Installation Cost in Montana: Where Every Dollar Goes

Whole-home generator installs in Montana run about $12,000 to $22,000. See where the money goes, from propane and altitude derating to permits and travel.

·October 26, 2026·8 min read

Whole-Home Generator Installation Cost in Montana: Where Every Dollar Goes

Most Montana homeowners spend roughly $12,000 to $22,000 to get a whole-home standby generator installed and running. The generator itself is often less than half of that. The rest goes into fuel, wiring, the transfer switch, the pad, the permit, and the miles a crew has to drive to reach you.

That last part matters more here than almost anywhere else. A generator job ten minutes from a shop in Billings is a different bill than one at the end of a gravel road outside Lincoln or Ekalaka. The breakdown below walks through each line item with approximate costs so you can read a quote and see where your money is going.

The Generator Unit Itself

An air cooled standby generator in the 20 to 26 kW range usually runs about $5,500 to $8,500 for the equipment alone. That size covers most homes up to about 3,000 square feet, including a furnace, well pump, refrigerator, and lights. Larger liquid cooled units in the 30 to 48 kW range cost $12,000 to $20,000 before installation and are usually reserved for big homes, ranches, or all electric houses.

Brand and controller features add or subtract a few hundred dollars. Units with load management modules can shed big loads like a water heater or dryer when the generator is near its limit. That feature often lets you buy a smaller generator than you would otherwise need.

Altitude Derating at Montana Elevations

Generators lose power as elevation rises because the thinner air carries less oxygen for combustion. Many manufacturers list a derate of roughly 3% to 4% per 1,000 feet above a baseline elevation. At Bozeman, around 4,800 feet, or Butte, around 5,500 feet, a 22 kW unit may deliver closer to 18 or 19 kW in practice.

Running on propane instead of natural gas trims output a bit more on many models. Put both together and a home in the Gallatin Valley or around Helena may need to step up one size from what a sea level sizing chart suggests. Ask your installer to show you the derated output alongside the nameplate rating.

Fuel: Propane Tanks and Long Gas Runs

Natural gas is available in much of Billings, Missoula, Bozeman, Great Falls, and Helena, along with other towns served by NorthWestern Energy or Montana Dakota Utilities. Outside those service areas, nearly every generator in the state runs on propane. Fuel setup can be the second biggest line item on a rural quote.

A 500 gallon propane tank is the common choice for a whole-home generator, since it holds enough to run a 22 kW unit through several days of outage. Buying that tank outright often costs about $1,800 to $3,500 installed, while leasing through a propane supplier lowers the upfront cost but ties you to that supplier. Some homes already have a 500 or 1,000 gallon tank for the furnace and can tap into it.

Trenching and Long Fuel Lines

Montana homes on acreage often have the tank set well away from the house, which means a long underground fuel line. Trenching and running gas line typically costs about $15 to $40 per foot, and frozen or rocky ground pushes that higher. A 150 foot run can add $2,500 to $5,000 on its own.

In town, natural gas jobs may need a meter upgrade if the existing meter cannot handle the furnace, water heater, and generator together. That is a call to the utility and can add a few weeks to the timeline.

Transfer Switch and Electrical Work

The automatic transfer switch is the piece that senses a power loss, starts the generator, and moves your home onto generator power. A whole-home switch rated for a 200 amp service typically runs about $700 to $2,000 for the equipment. Service rated switches can sit right at the meter and replace the main breaker.

Electrical labor to wire the switch, run conductors to the generator, and tie everything into the panel usually lands around $2,000 to $4,500. Older panels in farmhouses and cabins may need upgrades, which can add $1,500 to $3,500. If the generator sits far from the house, wire and conduit costs grow with every foot.

Well Pumps and Starting Loads

Most rural Montana homes rely on a private well, and the pump is often the hardest load for a generator to start. A submersible pump draws a large burst of current for a second or two when it kicks on. If the furnace blower and the pump start at the same moment, an undersized generator can stall.

Your installer should check the pump horsepower and plan for it. Soft start kits on the pump or on the central air unit cost about $300 to $600 and can make a smaller generator work. Livestock waterers and stock tank heaters on a ranch also need to be counted.

Cold Weather Starting Equipment

A generator that will not start at minus 25 is no help during a January outage in Havre or West Yellowstone. Cold weather kits typically include a battery warmer and an oil or crankcase heater, and they cost roughly $150 to $500 installed. Many Montana installers include them automatically.

Synthetic oil rated for cold starts is another small cost worth paying. Ask whether the unit's controller can run a weekly exercise cycle at a time of day when it is warmest.

Placement also counts in cold country. Snow drifts can bury air intakes, so the pad should sit where wind and plowed snow will not pile up against it.

Pad, Placement, and Site Prep

Most air cooled units sit on a composite pad that comes with the generator or on a small poured concrete pad. Site prep usually runs about $200 to $900, more if the ground needs leveling or gravel. Code sets minimum distances from windows, doors, and vents, which sometimes forces the unit farther from the panel.

Wildfire country adds another consideration. Keeping dry grass, firewood, and brush cleared around the generator lowers the chance that a hot exhaust or a fault starts a fire.

Permits and Inspection

Electrical work on a standby generator requires a permit and inspection in Montana. In much of the state, permits go through the Montana Department of Labor & Industry's Building Codes program, while cities with their own building departments handle permits locally. Expect permit fees of roughly $100 to $400 depending on the jurisdiction and job size.

Electricians must hold a license through the Montana State Electrical Board, and gas line work may require a separate inspection. Your installer should pull the permits and schedule inspections. Rural inspections can take a while to schedule, so build a little time into the plan.

Travel, Distance, and Rural Surcharges

Distance is the hidden line item on many Montana generator quotes. Crews based in Billings, Missoula, Bozeman, Kalispell, or Great Falls often add a trip charge for jobs more than 30 to 50 miles out. Multi day installs may include lodging or per diem for the crew.

These charges commonly range from $200 to $1,500 depending on how remote you are. A local electrician in a smaller town such as Lewistown, Miles City, or Dillon may cost less overall even if the hourly rate is similar.

Why Montana Homes Are Adding Generators

Wildfire risk has changed how some utilities run their lines. NorthWestern Energy and several rural electric cooperatives in Montana have adopted wildfire plans that can include public safety power shutoffs during high wind and dry conditions. Those shutoffs can last hours or days, often in late summer when wells and freezers matter most.

Winter storms are the other driver. Ice and heavy snow bring down lines across the Hi Line and in the mountains, and repair crews may take days to reach remote spans. For homes that depend on electric heat tape, a well, or medical equipment, a standby generator becomes a practical piece of the house.

Approximate Cost Summary

Line itemApproximate cost in Montana
20 to 26 kW air cooled generator$5,500 to $8,500
Automatic transfer switch$700 to $2,000
Electrical labor$2,000 to $4,500
500 gallon propane tank$1,800 to $3,500
Fuel line trenching per foot$15 to $40
Cold weather kit$150 to $500
Pad and site prep$200 to $900
Permit and inspection$100 to $400
Rural travel surcharge$200 to $1,500

Annual maintenance runs about $200 to $450 for an oil change, filters, and a load test. Get at least three quotes from licensed electricians who install standby generators, and ask each one to list these line items separately. More home cost guides for the state are on our Montana homeowner blog.

Frequently Asked Questions

What size generator does a Montana home need?

Most homes with gas or propane heat and a well do well with 22 to 26 kW after altitude derating. All electric homes or houses with electric baseboard heat often need 30 kW or more.

How long will a 500 gallon propane tank run my generator?

A 22 kW generator at half load burns roughly 2 to 3 gallons per hour. A tank filled to 80% holds about 400 gallons, which works out to roughly six to eight days of continuous running.

Can I install a standby generator myself in Montana?

Homeowners can do some electrical work on their own primary residence under state rules, but the work still needs a permit and inspection. Gas connections and transfer switch wiring are best left to licensed pros.

Do I need a generator if my utility does wildfire shutoffs?

Not always, but it helps if you rely on a well, sump pump, or medical device. A portable generator with a manual interlock is a cheaper backup option at around $2,000 to $4,000 installed.